10 Questions to Ask a Commercial Concrete Contractor Before You Hire One
Concrete is the one part of a commercial project you cannot easily undo. A slab poured on a bad base, a footing sized for the wrong soil, a parking lot with the drainage backwards: each one is permanent, expensive to correct and invisible until it fails. The good news is that the contractors who get it right answer the same ten questions the same way. Ask these before you hire anyone for commercial concrete work in the Bay Area, and listen for the answers below.
Questions 1 to 3: the ground and the engineering
1. Have you read the soils report, and what does it change? Bay Area soils range from expansive clay in the Tri-Valley and East County to bay mud and fill along the shoreline. The report dictates base preparation, slab thickness, reinforcement and footing depth. A contractor who prices the job without it is guessing.
2. Who engineers the structural concrete? Footings, grade beams, retaining walls and slabs that carry equipment need a licensed engineer’s drawings. The answer should name the engineer and describe how the contractor coordinates with them.
3. How will you prepare the base? Listen for compaction testing, the base material and thickness, a vapor barrier under interior slabs, and how the subgrade will be protected if it rains before the pour.
Questions 4 to 6: the pour
4. What mix are you using and why? Strength, air entrainment, admixtures for hot weather and for pumping, and fiber or rebar reinforcement should match the use: a loading dock is not a sidewalk.
5. How do you document the pour? On structural work the answer is slump tests, cylinders sent to a lab and a written record for each truck. We do this on every structural pour and hand the results over at close-out.
6. How do you handle joints and curing? Control joints placed and cut on time are what keep a slab from cracking where it wants to; curing compound or wet curing is what gives it its strength. If the contractor cannot explain the joint layout, the slab will crack randomly within a year.
Questions 7 and 8: accessibility and drainage
7. How will you verify ADA slopes? Parking stalls, access aisles, ramps and paths of travel have maximum slopes and cross-slopes, and inspectors measure them. The answer should include checking the forms before the pour and the finished surface after it, because grinding a ramp that is a half-percent off is expensive.
8. Where does the water go? Every exterior slab and parking lot is a drainage design. Ask to see the grading plan and how the contractor sets the forms to it. Ponding on a new parking lot is a sign the question was never asked.
Questions 9 and 10: the business side
9. Show me three commercial concrete projects like mine, nearby. Then go stand on them. Ours include a dealership service-center slab, multifamily foundations, a hillside retaining wall and the foundations and slab for a steel building in Livermore; see the recent projects page.
10. What is the price, exactly? A fixed-price, itemized proposal with the scope, the mix, the reinforcement, the testing, the exclusions and the schedule by phase. Changes only by signed change order. Lien releases with each payment. License, bond and insurance certificates attached before mobilization.
What the right answers have in common
Every good answer above comes back to the same thing: the contractor treats concrete as engineering, not as pouring. They read the soils report, they coordinate the engineer, they prepare and test the base, they document the pour, they place the joints, they check the slopes, and they put all of it in writing. That is how Smith & Son runs commercial concrete and foundation work across the East Bay, under a fixed-price proposal with daily site supervision and a close-out package with the test results, as-builts and warranties.
A note on phasing in occupied properties
Most commercial concrete happens around a business that is still open: a parking lot that cannot close entirely, a loading dock that is used daily, a slab replacement inside a working warehouse. Ask how the contractor phases the work, how long each section is out of service, how early pours and fast-setting mixes can shorten that, and who communicates with the tenants. The schedule you want is one that is written by section, with cure times included, so nobody drives on a slab that is not ready.
Commercial Concrete FAQ
How long before a new commercial slab or parking lot can be used?
Foot traffic in a day or two, light vehicles in about a week, full design strength at 28 days. Fast-setting mixes can shorten the early window where a business cannot wait.
Do commercial concrete projects need a permit?
Structural concrete, retaining walls above the city’s height threshold, and anything tied to a building do. Parking lots and site work usually need grading or encroachment permits. We tell you which apply and pull them.
Why do new slabs crack?
Almost always the base or the joints: an uncompacted or wet subgrade, or control joints missing or cut too late. A properly prepared base and timely joints keep cracking where it belongs.
Do you test the concrete?
Yes. On structural pours we record slump and cast cylinders for lab testing on every truck, and the results are in your close-out package.
What commercial concrete work does Smith & Son do?
Slabs, foundations and footings, grade beams, retaining walls, parking lots, sidewalks, ADA ramps, loading docks, dumpster pads and concrete repair across the East Bay, plus the foundation and slab work on our own commercial construction projects.
Ask Us the Ten Questions
Smith & Son pours and finishes commercial concrete across Contra Costa, Alameda, Solano and Napa counties: slabs, foundations, parking lots, retaining walls and ADA work, engineered for local soils and documented pour by pour. Call (925) 387-0684 or request a quote.
Get In Touch With Us!
Planning a slab, foundation or parking lot project? Smith & Son is a licensed Bay Area commercial general contractor with its own concrete capability. See our commercial concrete service or request a quote today.